Have you tried setting the Gateway using Yast?
Russ Wright wrote:
> Hello Sluggers!
> I need some help fixing a networking problem. The network funcitons properly
> under Windows so I know the hardware is working. The problem seems to be
> linux specific. I have a wireless network in my house and I cannot get
> outside of my local area network. I am running Suse 9.0 pro and have a
> Linksys WUSB11 ver 2.6 wireless nic. I am using the at76c503 - linux driver
> for Atmel at76c503 based usb wlan adapters.
> http://at76c503a.berlios.de/
>
> I can hotplug the wireless nic and it is detected and the driver modules load
> properly. I confirmed this by doing
> #>lsmod
> Module Size Used by Tainted: P
> at76c503-rfmd 39360 0 (unused)
> usbdfu 7820 0 [at76c503-rfmd]
> at76c503 49824 0 [at76c503-rfmd]
>
> I then confirm the device is recognized and do a #> iwconfig
> lo no wireless extensions.
> eth0 no wireless extensions.
> sit0 no wireless extensions.
> eth1 ATMEL RFMD503A ESSID:"linksys" Nickname:"linksys"
> Mode:Managed Channel:6 Access Point: 00:06:25:55:C9:FD
> Bit Rate:11Mb/s
> RTS thr=2347 B Fragment thr=2346 B
> Encryption key:off
> Link Quality:100 Signal level:65 Noise level:0
> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
> Tx excessive retries:0 Invalid misc:0 Missed beacon:0
>
> So I issued an #>ifup eth1
> warning: using NO encryption
> ERROR: command 'iwconfig eth1 nick linux' returned
> Error for wireless request "Set Nickname" (8B1C) :
> SET failed on device eth1 ; Operation not supported.
> Starting DHCP Client Daemon on eth1... . IP/Netmask: 192.168.1.102 /
> 255.255.255.0
>
> The error messages are no biggie the important part is that I get an IP
> address.
>
> I also check the config:
> #> ifconfig
> eth1 Link encap:Ethernet HWaddr 00:06:25:19:9A:3C
> inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0
> inet6 addr: fe80::206:25ff:fe19:9a3c/64 Scope:Link
> UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:58 errors:0 dropped:0 overruns:0 frame:0
> TX packets:63 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:100
> RX bytes:6763 (6.6 Kb) TX bytes:5274 (5.1 Kb)
>
>
> When I issue #> route
> Kernel IP routing table
> Destination Gateway Genmask Flags Metric Ref Use Iface
> 192.168.1.0 * 255.255.255.0 U 0 0 0 eth1
>
> Notice the missing gateway I cannot get outside my local area network. If I
> manually add the route then it works.
>
> # route
> Kernel IP routing table
> Destination Gateway Genmask Flags Metric Ref Use Iface
> 192.168.1.0 * 255.255.255.0 U 0 0 0 eth1
> default 192.168.1.1 0.0.0.0 UG 0 0 0 eth1
>
> So any Ideas on the problem?
>
>
>
> -----------------------------------------------------------------------
> This list is provided as an unmoderated internet service by Networked
> Knowledge Systems (NKS). Views and opinions expressed in messages
> posted are those of the author and do not necessarily reflect the
> official policy or position of NKS or any of its employees.
>
>
>
-----------------------------------------------------------------------
This list is provided as an unmoderated internet service by Networked
Knowledge Systems (NKS). Views and opinions expressed in messages
posted are those of the author and do not necessarily reflect the
official policy or position of NKS or any of its employees.
This archive was generated by hypermail 2.1.3 : Fri Aug 01 2014 - 18:02:59 EDT